Where to Put the Projector
Height, masks, mounting and beam ends: how to choose positions that keep beams away from people.
Where you put the projector decides most of the safety of the show. If the beams naturally stay away from people, everything else gets easier. If they do not, you will spend the night managing a problem that you built into the rig.
Mount as high as you can. Height keeps beams away from spectators, and it gives better effects over the audience. A projector 5.5 metres up on a truss, in a hall with an 8 metre ceiling, is a good position. A club with a 3.5 metre ceiling is much harder. Beams above the spectator limit must stay 3 metres above where people stand, and a low room may not allow that. In a low room you can confine the beams to the stage with a mask and a barrier. Or you can lower the power until the exposure is under the limit, and assess it properly. [cl. 6.10]
Fit a physical mask to the projector. A steel plate over the window that blocks everything below horizontal is a common choice. If the software misbehaves or the projector shifts, the beam still cannot go down at the crowd. Software masks are weaker, so use one only when a physical mask is not practical. The size or gain control on a projector is not a mask. Test every mask by trying to send beams past it. [cl. 6.2]
Rig it properly. Hang the projector from a rigging point or truss that is rated for the weight, using clamps that are rated for the job. Ask the venue what each point can carry, and use a qualified rigger if you are not one. Never hang a projector from a pipe, a cable tray or anything else that was not built to take the load.
The mount must not move. Bass vibration, a knock from a crew member, wind and a shared truss can all shift a projector, and a beam that moves a few degrees can end up somewhere very different. Use a solid clamp and a rigid bracket, tighten everything fully, and do not rely on a cable or a tilt head that can droop over time. Support the cables so they do not pull on the projector. Then check that the mask still works at that position. A moving-head projector needs mechanical stops, not just a software limit. Bounce mirrors and targets need the same care: mount them rigidly and mask them. [cl. 6.3, 6.4, 6.6, 6.11]
Always add a safety wire. This is a second, separate attachment, such as a rated steel safety bond. It goes around the truss or rigging point and through a strong part of the projector body, not through the clamp it is meant to back up. Keep it short, so the projector cannot fall far or swing. If the clamp ever fails, the wire stops the projector hitting the crowd, and it limits how far the beam can swing. Check the wire and the clamp every time you set up, and record that you did.
Plan where every beam ends. A beam that runs past the back wall, across an exit or onto a glossy surface is a problem. Each beam should finish on a matt surface or a beam stop that you have checked. Where beams from two projectors cross, assess them together. [cl. 9.4.2]
Choose the control position as carefully as the projector. The operator must see every projection from there. Put one hard-wired e-stop under the operator's hand and a second one where the stage manager stands. Pressing Esc or sending a DMX blackout is not an e-stop, because it depends on the control signal. Label each projector the same way on your plan and in your Display Safety Record. [cl. 6.8]
Do not rely on distance. A show beam can stay hazardous for hundreds of metres, so a projector at the back of the room is not safe just because it is far away. Putting the projector behind the audience and firing towards the stage is not automatically safer either. The beams still pass over people's heads, and the projector sits where someone can reach it. Whatever position you choose, keep beams away from people with position, masks and barriers. [cl. 6.2]
Want to learn more? The LSO Certification course covers this topic in depth with interactive exercises, quizzes, and a final exam. Module 1 is free to preview.